SNOW THROWERMODELSSnow Boss 850WSnow Boss 1150WOPERATOR’S MANUALPRINTED IN U.S.A.IMPORTANT: READ SAFETY RULES AND INSTRUCTIONS CAREFULLYWHITE OUTDOOR
10snow. Adjust downward (to raise the shave plate) when using on gravel or crushed rock.• Be certain to follow the precautions found in the To Stop En
11Drive WheelsThe wheels may be adjusted for two different methods of operation. The adjustment is made by placing the click pins in one of two differ
12Traction Control / Auger Control LockThe cams on the ends of the control rods which interlock the traction drive and auger drive controls must be lu
13• Drain the gasoline from the snow thrower, or place a piece of plastic film under the gas cap.• Tip the snow thrower up and forward so that it rest
14Figure 16• Holding the friction wheel assembly, slide the hex shaft out of the left side of the frame. The spacer on the right side of the hex shaft
15SECTION 8: TROUBLE SHOOTING Problem Cause RemedyEngine fails to start 1. Fuel tank empty, or stale fuel.2. Blocked fuel line.3. Choke not in ON pos
16Notes
1721246710914118161315Models 850W & 1150W513317Ref. No.Part No. Part Description1. 618-0123 RH Housing (Incl. Ref. 17, 18)2. 618-0418 LH Housing w
18Models 850W / 1150W141021412163205866616063676557585554817112221184111151952714494227364430283244481023383535399432625314041950243731459514046475359
19Models 850W / 1150WRef. No.Part No. Part Description1. 684-0008A Shift Arm Assembly2. 710-0262 Carriage Bolt 5/16-18 x 1.5”3. 710-0449 Carriage Bolt
2TABLE OF CONTENTSContent PageImportant Safe Operation Practices...3Assembling Your Sn
20Models 850W / 1150W12345678910111214151316102122232523222618272813303132331618353436373839414042174039292420919
21Models 850W / 1150WRef. No.Part No. Part Description1. 712-0116 Lock Jam Nut 3/8-242. 756-0178 Flat Idler 3. 784-5632A Auger Idler Arm4. 710-0459A H
22Models 850W / 1150W1234567489101112131415161718191916161620212223242526272829303132333435IMPORTANT: For a proper working machine, use Factory Approv
23Models 850W / 1150WRef. No.Part No. Part Description1. 710-1652 Hex Washer Screw 1/4-20 x .6252. 731-1324 Belt Cover3. 732-0710 Extension Spring4. 7
24Models 850W / 1150W727152844292381111364711505211333373337109131342631301694317344634181963918244034321420323538454034323832201494857493647364711414
25Models 850W / 1150WRef. No.Part No. Part Description1. 618-0043 Dogg Assembly: RH2. 618-0044 Dogg Assembly: LH3. 618-0303B Shift Assembly: Steerable
26
27
MANUFACTURER’S LIMITED WARRANTY FOR:The limited warranty set forth below is given by White Out-door Products Co. with respect to new merchandise pur-c
3SECTION 1: IMPORTANT SAFE OPERATION PRACTICESWARNING: This symbol points out important safety instructions which, if not followed, could endanger th
43. The clutch levers must operate easily in both directions and automatically return to the disengaged position when released. 4. Never operate with
5SECTION 2: ASSEMBLING YOUR SNOW THROWERNOTE: Any reference in this manual to the left or rightside of the snow thrower is observed from theoperator’
6Final AdjustmentsAuger Control AdjustmentCheck the adjustment of the auger control as follows:• Push forward on the auger control until the small rub
7• Recheck the adjustment and repeat adjustment as necessary. • Retighten the jam nut to secure the cable when correct adjustment is reached.NOTE: If
8Electric Chute-Rotation SwitchThe electric chute-rotation switch is located on the leftside of the snow thrower dash panel. See Figure 7.To change th
9• If your home electrical system is grounded, but a three-hole receptacle is not available, one should be installed by a licensed electrician before
Comments to this Manuals