OPERATOR’S MANUALSNOW THROWERMODEL31AH7Q3G190PRINTED IN U.S.A.IMPORTANT: READ SAFETY RULES AND INSTRUCTIONS CAREFULLYWHITE OUTDOOR PRODUCTS COMPANY P.
10Electric Starter:• Connect power cord to switch box on engine, then to 120 volt AC receptacle. With the engine running, push starter button and spin
11• Tip the snow thrower forward, allowing it to rest on the auger housing.• Remove the frame cover underneath the snow thrower by removing the six se
12mechanism at least once a season. Use engine oil or a spray lubricant. Avoid getting oil on the friction wheel rubber and aluminum drive plate. Refe
13Shave Plate and Skid ShoesThe shave plate and skid shoes on the bottom of the snow thrower are subject to wear. They should be checked periodically
14Figure 15Servicing Friction Wheel RubberThe rubber on the friction wheel is subject to wear and should be checked after 25 hours of operation, and p
15WARNING: Drain fuel into an approvedcontainer outdoors, away from an openflame. Allow engine to cool. Extinguishcigarettes, cigars, pipes, and other
16SECTION 8: TROUBLESHOOTINGProblem Cause RemedyEngine fails to start 1. Fuel tank empty, or stale fuel.2. Blocked fuel line.3. Choke not in the ON p
17Model 31AH7Q3G190Ref. No.Part No. Part Description1. 618-0123 RH Housing2. 618-0418 LH Housing w/Fitting3. 710-0642 Self Tapping Screw, 1/4-20 x .75
18Model 31AH7Q3G19014102141216320586661606367655758555481711222118411115195271423383535399432625314041950243731459514046475359296869692782707272732768
19Model 31AH7Q3G190Ref. No.Part No. Part Description1. 684-0008A Shift Arm Assembly2. 710-0262 Carriage Bolt 5/16-18 x 1.5”3. 710-0449 Carriage Bolt 5
2TABLE OF CONTENTSContent PageImportant Safe Operation Practices...3Assembling Your Sn
20Model 31AH7Q3G19012345678910111214151316102122232523222618272813303132331618353436373839414042174039292420919
21Model 31AH7Q3G190Ref. No.Part No. Part Description1. 712-0116 Lock Jam Nut 3/8-242. 756-0178 Flat Idler 3. 784-5632A Auger Idler Arm4. 710-0459A Hex
22Model 31AH7Q3G1901123456748910111213141516171819191616162021222324252627282930
23Models 31AH7Q3G190Ref. No.Part No. Part Description1. 710-1652 Hex Washer Screw 1/4-20 x .6252. 731-1324 Belt Cover3. 732-0710 Extension Spring4. 71
2425192627242322211617181920293031232323430227261925362124232212 230101819202113111415937654324039383237Models 31AH7Q3G19028835
25NOTE: For painted parts, please refer to the listof color codes below. Please add the applicablecolor code, wherever needed, to the part numberto or
26Models 31AH7Q3G1901263101278549131514171619202222201928211821181513142931323030323437383623352739114041424443455146474852465351545554501617493756562
27Models 31AH7Q3G190Ref. No.Part No. Part Description1. 720-0223 Grip2. 710-0604 Tap Screw, 5/16-18 x .6253. 784-5642 Track Lockout Plate4. 710-0157 H
MANUFACTURER’S LIMITED WARRANTY FOR:The limited warranty set forth below is given by White Out-door Products Co. with respect to new merchandise pur-c
3SECTION 1: IMPORTANT SAFE OPERATION PRACTICESWARNING: This symbol points out important safety instructions which, if not followed, could endanger th
43. The clutch levers must operate easily in both directions and automatically return to the disengaged position when released. 4. Never operate with
5SECTION 2: ASSEMBLING YOUR SNOW THROWERNOTE: Any reference in this manual to the left or rightside of the snow thrower is observed from theoperator’
6Final AdjustmentsAuger Control AdjustmentCheck the adjustment of the auger control as follows:• Push forward on the auger control until the small rub
7• Recheck the adjustment and repeat adjustment as necessary. • Retighten the jam nut to secure the cable when correct adjustment is reached.If you ar
8Electric Chute-Rotation SwitchThe electric chute-rotation switch is located on the leftside of the snow thrower dash panel. See Figure 7.To change th
9SECTION 4: OPERATING YOUR SNOW THROWERBefore StartingWARNING: Read, understand, and followall instructions and warnings on themachine and in this ma
Comments to this Manuals