White Outdoor Series 79G Operator's Manual download pdf (Page 16)

 SECTION 5— OPERATION SECTION 5— OPERATION

Once activated (indicator light ON), the tractor can be 4.

driven in reverse with the cutting blades (PTO) engaged.

Always look down and behind before and while backing to 5.

make sure no children are around.

After resuming forward motion, return the key to the 6.

NORMAL MOWING position.

*.1035"/5The REVERSE CAUTION MODE will remain

activated until:

The key is placed in either the NORMAL MOWING a.

position or STOP position.

The operator engages the parking brake by fully b.

depressing the brake pedal and holding it down

while moving the parking brake lever into the PARK

BRAKE position.

Engaging the Parking Brake.

To engage the parking brake:

Fully depress the brake pedal and hold it down with your 1.

foot.

Move the parking brake lever all the way down and into the 2.

ON position.

Release the brake pedal to allow the parking brake to 3.

engage.

To release the parking brake:

Depress the brake pedal and move the parking brake lever 1.

out of the ON position and into the OFF position.

Setting the Cutting Height

Select the height position of the cutting deck by placing 1.

the deck lift lever in any of the six different cutting height

notches on the right side of the fender.

Adjust the deck wheels, if equipped, so that they are 2.

between ¼-inch and ½-inch above the ground when the

tractor is on a smooth, flat surface such as a driveway.

8"3/*/(Keep hands and feet away from the

discharge opening of the cutting deck.

NOTE: On models so equipped, the deck wheels are an anti-scalp

feature of the deck and are not designed to support the weight

of the cutting deck.

Refer to Leveling the Deck on page 20 of this manual for more

detailed instructions regarding various deck adjustments.

Starting the Engine

8"3/*/(Do not operate the tractor if the

interlock system is malfunctioning. This system was

designed for your safety and protection.

NOTE: Refer to the TRACTOR SET-UP of this manual for Gasoline

and Oil fill-up instructions.

Insert the tractor key into the ignition switch.1.

Place the PTO 2. (blade engage) lever in the disengaged (OFF)

position.

Engage the tractor’s parking brake.3.

Activate the choke control.4.

Turn the ignition key clockwise to the START position. After 5.

the engine starts, release the key. It will return to the ON (or

Normal Mowing) position.

*.1035"/5Do NOT hold the key in the START position for

longer than ten seconds at a time. Doing so may cause damage

to your engine’s electric starter.

After the engine starts, deactivate the choke control and 6.

place the throttle control in the FAST position.

NOTE: Do NOT leave the choke control on while operating the

tractor. Doing so will result in a “rich” fuel mixture and cause the

engine to run poorly.

Stopping the Engine

8"3/*/(If you strike a foreign object, stop the

engine, disconnect the spark plug wire(s) and

ground against the engine. Thoroughly inspect the

machine for any damage. Repair the damage before

restarting and operating

If the blades are engaged, place the PTO 1. (blade engage)

lever in the disengaged (OFF) position.

Turn the ignition key counterclockwise to the STOP 2.

position.

Remove the key from the ignition switch to prevent 3.

unintended starting.

Driving The Tractor

8"3/*/(Always look down and behind before

and while traveling in reverse to avoid a back-over

accident.

8"3/*/(Before leaving the operator’s position.

Always place the PTO (blade engage) lever in the

disengaged (PTO OFF) position, place speed control

lever in neutral, set parking brake, stop engine and

remove key to prevent unintended starting.Depress

the brake pedal to release the parking brake and let

the pedal up.

Move the throttle lever into the FAST (rabbit) position.1.

NOTE: Always operate the tractor with the throttle control lever

in the FAST (rabbit) position for the most efficient use of the

cutting deck or other (separately available) attachments.

Release the parking brake by depressing the brake pedal2.

Position the speed control lever in desired position. The 3.

further forward or rearward that the lever is moved, the

faster the tractor will travel.

8"3/*/(Do NOT attempt to change the

direction of travel when the tractor is in motion.

Always bring the tractor to a complete stop before

moving the speed control lever from forward to

reverse or vice versa. Failure to do so could result in

serious damage to your tractor’s transmission.

*.1035"/5First-time operators should use slower speeds.

Become completely familiar with the tractor’s operation and

controls before operating the tractor in at higher speed.

1 2 ... 11 12 13 14 15 16 17 18 19 20 21 ... 33 34

Comments to this Manuals

No comments

White Outdoor Series 79G Operator's Manual Page 16

Comments to this Manuals

Related products and manuals for Snow throwers White Outdoor Series 79G