Chipper ShredderVacuumModel NumberYard Boss 950 PRINTED IN U.S.A.OPERATOR’S MANUALFORM NO. 770-10052C.fm(8/01)IMPORTANT: READ SAFETY RULES AND INSTRUC
10SECTION 5: ADJUSTING YOUR CHIPPER SHREDDER VACUUM WARNING: Do not at any time make anyadjustments without first stopping engine,disconnecting spark
11MaintenanceEngineRefer to the separate engine manual for all engine maintenance instructions.• Check engine oil level before each use as instructed
12NOTE: Be certain to reassemble the flail screen withthe curved side down.• Reattach the discharge chute assembly with the hardware previously remove
13• Slide the friction wheel assembly up onto the shift mechanism and then slide the hex shaft back into the unit.• Reassemble in reverse order and re
14SECTION 7: TROUBLESHOOTINGNOTE: For repairs beyond the minor adjustments listed above, contact your nearest authorized service dealer. Problem Caus
15NOTES
16Model 950 1234567865791110121313141516171718192021222324252627282930313233193435361237363839404142434445464748484950515253
17Model 950Ref. No.Part No. Part Description1. 781-0633 Chute Flap Strip2. 735-0249 Chute Flap3. 728-0175 Pop Rivet4. 731-1574 Chipper Chute5. 710-075
18Model 950123456678891010111112121212131415161717181920211622232425262728293031
19Model 950Ref. No.Part No. Part Description1. 720-0232 Shift Knob2. 784-0297A Shift Lever3. 735-0126 Rubber Washer4. 736-0300 Flat Washer5. 712-0116
2TABLE OF CONTENTSContent PageImportant Safe Operation Practices...3Assembling Your Ch
20Model 9501234567891011121314151618171920212022232425926272829303031323334353637383940414243444546474849505051525248495354
21Model 950Ref. No.Part No. Part Description1. 751-0603 Fuel Cap2. 751-0610 Gas Tank - 1 Gallon3. 712-3027 Hex Lock Nut 1/4-204. 736-0173 Flat Washer
22Model 9501234565789310111213141516171819202122232425262627282930313233348123536433635373838394041424344
23Model 950Ref. No.Part No. Part Description1. 618-0168 Transmission Assembly2. 750-0981 Spacer .782 ID x 1.0 OD3. 710-3008 Hex Cap Screw 5/16-18 x .7
MANUFACTURER’S LIMITED WARRANTY FOR:The limited warranty set forth below is given by White Out-door Products Co. with respect to new merchandise pur-c
3SECTION 1: IMPORTANT SAFE OPERATION PRACTICESWARNING: This symbol points out important safety instructions which, if not followed, could endanger th
4j. To reduce a fire hazard, keep machine free of grass, leaves, or other debris build-up. Clean up oil or fuel spillage and remove any fuel soaked de
5WARNING: - YOUR RESPONSIBILITY: Restrict the use of this power machine to persons who read,understand and follow the warnings and instructions in thi
6Attaching The Front Wheels• Tilt the unit backward, so that it rests on the handle (place a piece of cardboard under handle to avoid scratches). Remo
7Figure 5 Clutch Cable AdjustmentAdjust the hex nuts at the cable bracket so there is no slack in the cable, but the cable should not be tight. Do n
8Shift LeverThe shift lever is located on the top right hand side of unit. It is used to adjust the ground speed of the chipper shredder vacuum when t
9• Engines with choke lever:Move choke lever on engine to CHOKE position. (A warm engine may not require choking).• Engines with primer:Prime engine a
Comments to this Manuals